The TZ16 unit is a two-level 16×16 video and audio balanced stereo matrix.

It can be programmed to operate with Y/C (8×8), Y Cb Cr (5×5) and RGBS (4×4) signals.

Output 16 can operate as preview.

It can be controlled by a computer with RS232 serial interface and optional LAN.

Technical Specifications

VIDEO
Input type	AC coupled
Input return loss	40 dB at 5 MHz
Output return loss	>40 dB at 5 MHz
Frequency response	-0.1 dB at 10 MHz;
	-1 dB at 60 MHz;
	-3 dB at 170 MHz
	-3 dB One to All, worst case, 150 MHz
Differential gain	±0.3%
Differential phase	+0.2°
Crosstalk (worst case)	better than 80 dB at 5 MHz
Hum &: Noise	-90 dB unweighted

AUDIO
Input type	differential with Phoenix screwtype removable
Input coupling	AC
Input impedance	22KΩ single ended,
	44KΩ differential
Input/output level	+16 dBm max (balanced)
Output impedance	600Ω
Frequency response	-1 dB from 3 Hz to 600 KHz
Distortion
Crosstalk (worst case)	60 dB at 20 KHz
Hum &: Noise	-80 dBm unweighted
Remote control	IR, RS232, LAN
****
Mains input	230 VAC / 115 VAC (selectable)
Power consumption	10 VA
Size (WxDxH)	483x130x176 mm
Weight	6 kg
Operating temperature range	0÷45°C
Safety	according to EN 60065
EMC	according to EN 55103-1 and EN 55103-2

• Video inputs with BNC in loop
• Switching in the frame interval
• Keypad-programmable preview output
• Only VIDEO, only AUDIO, AFV
• Save last configuration command
• 8 presets that can be recalled from keypad and RS232
• IR remote control (optional)
• LAN control (optional)

Brochure / leaflet for TZ16VBA:
Elpro_TZ16VBA.pdf

USER MANUAL:

User Instruction Manual for Elpro TZ16VBA
Elpro_TZ16VBA_user_manual_eng.pdf

CE CERTIFICATION:

CE Conformity document for TZ16VBA
CE Conformity

DOCUMENTATION FILES

User manual for LAN202
LAN202_note_eng.pdf

How to control TZ16VBA by CNS1000
CNS1000_conn_TZ16VBA_eng.pdf

WINDOWS DRIVERS

Control Software for TZ16VBA
TZ16VBA_driver_1_4.zip

Available Software:

Software to upload firmware into Elpro units
Elpro_uploader.zip

Software for Ethernet interface configuration and virtual COM management – Win 32bit
150727 Tibbo tdst-5-09-12-x86-01.zip

Software for Ethernet interface configuration and virtual COM management – Win 64bit
150727 Tibbo tdst-5-09-12-x64-01.zip

FIRMWARE

Firmware updating of the Elpro devices is possible using the specific utility UPLOADER.

This software should be downloaded and installed on a PC in a Windows environment.

To perform the updating of the firmware it is necessary to connect the device to the PC serial line and therefore to perform the action (typical for every device) to put the device in UPGRADE MODE.

Then load the .hex file of the new firmware version and start uploading to the device.

At the conclusion of the updating it is necessary to turn OFF and ON again the device.

How to set the TZ16VBA
in UPGRADE MODE

Turn the TZ16 ON holding the key IN16 pressed.

The UPGRADE MODE is signaled with the leds OUT8 and OUT9 lighted.

Firmware notes:

Audio switching bug fixed

Current release: 2.3

MD5: D2D6077F6F213A6B186A3FD85523EE92

Elpro_FW_TZ16VBAr23.zip

High Resolution Images

Download here the available Hi-Res images of TZ16VBA.